It is very easy and simple to boost my Intex saltwater system. You have to follow some points, like the LED screen will display code “80” when the “Boost” button is pressed. This will increase chlorine output to meet the owner’s manual’s requirements. Press and hold the “Boost” button for 5 seconds until the indicator turns off to cancel the boost cycle.
A salt chlorine generator is a filtering system that cleans a saltwater pool. The system cleans the pool by converting salt to chlorine using electricity. Chlorine tablets or granules are physically added to a chlorinated pool regularly for the same reason.
What is the boost button on Intex saltwater system?
Boost just runs the SWG for a fixed somewhat long period and stops, which does whatever it does. That usually raises the chlorine level, but isn't usually even close to shocking.What does pool pump boost do?
The boost feature on a SWG simply turns the unit on at 100% for 24 hours. Every once in a long while that might be useful, but for ordinary situations it is not useful. If you are shocking the pool you want the FC level to go up quickly, which a SWG won't do.When should I raise my saltwater pool?
Owners and operators should engage the “boost cycle1” (which increases the chlorine level) to oxidize impurities on a regular basis according to manufacturer's instructions or at least once per week. The boost cycle should also be used when anticipating an influx of additional swimmers.How much salt do I put in my saltwater Intex?
The ideal salt level in the pool water is between 2500-3500 ppm (parts per million) with 3000 ppm being optimal. A too low salt level will reduce the efficiency of the Saltwater System and result in low chlorine production.How long should I run my Intex saltwater system?
First make sure you run just the filter pump for at least six hours to ensure the salt you've added has dissolved properly. Then you can run the salt water system fir the time recommended in the manual. If it's very hot and sunny you should run it for four hours for the 16'x48" pool.What does FP mean on pool pump?
"FP" is a feature of the combination systems (chlorinator and filter pump together in one) that stands for "Filter Pump".Why is my pool pump pressure so low?
When the pressure is lower than normal, this usually indicates a flow problem, and usually something is blocking or restricting water flow into the pool pump. It's never a problem after the pool pump, because after the impeller, the pool water is under pressure, and obstructions result in higher than normal pressure.Why does my pool have no flow?
The most common reason for low or no flow is that the baskets are full of debris. By checking and emptying both the skimmer basket (by the pool) and the pump basket (inside the pump) will free up the water flow, allowing the system to fully 'prime' and function at full capacity.How do I get water to circulate in my pool?
It's good practice to point your return jets in a direction that will circulate the water in your pool. If your pool only has one jet, point the jet toward the skimmer and downward. This will circulate the water, and push the water at the bottom of the pool to the surface.Why does my pool vacuum not have suction?
Rule out the obvious causes of poor vacuum first. Make sure the water level in the pool is sufficient and air is not being sucked in through skimmer inlets. Add water to the pool to submerge the skimmers if necessary. Verify that the pump strainer basket and the skimmers are free of debris that may obstruct water flow.Why does my Intex saltwater system keep saying low salt?
The pool pump filter is so small, that if you don't keep it cleaned out several times a day, it clogs and seriously decreases the water flow, causing a low salt reading and low chlorine output, due to the fact that the water is not moving quickly and strong enough through the SWS.What happens if salt level is too high in pool?
Highly excessive salinity levels (over 6,000 ppm) will cause corrosion damage to metallic equipment, such as ladders and handrails. The salt will be diluted as fresh water will be added when the pool is filled up with rain and by tap to keep the pool level up.Can you use saltwater in an Intex pool?
But what you might not know is that they can be easily converted to become a saltwater Intex pool. Switching from chlorine to saltwater can be a great choice for pool owners who have sensitivities or children with allergies and for those who don't want to be caught up on the incoming chlorine shortage.Are you supposed to shock a saltwater pool?
So, not only is shocking a saltwater pool okay, but it's actually important to your pool's health. Shocking is the process in which you overload your pool with chlorine (3-5 times the normal amount) to improve your pool's cleanliness and kill off organic matter.How often do you add salt to a saltwater pool?
Annual booster additions of pool salt are usually required, but only to replace salt lost from backwashing, splashout or lowering the water for winter. If you fully drain the pool for maintenance, you will need to replace all of the pool salt.What happens if salt level is too low in pool?
If the level is low, determine the number of gallons in the pool and add salt according to the chart below. A low salt level will reduce the efficiency of your salt chlorinator and result in low chlorine production. A high salt level can cause your chlorinator to shutdown and may begin to give your water a salty taste.Why does my salt water pool look cloudy?
Just like a chlorine-based pool, saltwater pools turn cloudy when chemicals are not balanced. You need to ensure that all chemicals are balanced all the time to avoid cloudy water and growth of algae. The major causes of cloudiness are chlorine, pH, Salinity, total alkalinity, cyanuric acid, and calcium hardness.Can too much salt make a pool cloudy?
You guessed it, cloudy or milky pool water. Or even algae. Sometimes the temperature or flow sensors in the salt generator system can be faulty too, which will cause the salt cell to shut off or reduce the chlorine output. This can also cause a cloudy saltwater pool.Why is my pool vacuum not picking up dirt?
When a suction cleaner is sluggish or slow, it's usually a clogged pump basket or dirty filter that is to blame. Other problems include holes in the cleaner hose, sucking air into the hose, or the filter pump could be drawing in air, reducing water-flow volume.Why is skimmer suction low?
Low water level or low PSI can also make your pool skimmer to lose suction power. That means you find more trash floating on the water, which makes it unsightly to swim. You should ensure that the water level reaches at least half of the skimmer opening.What direction should my pool Jets face?
The best way to position your pool jets is angled slightly downward and all pointing at the same direction or depending on the shape of your pool, that will create one “flow” or circular motion in your pool. The direction should be away from the skimmers.What direction should pool jets point?
The jets should all point in the same direction, ideally at a 45-degree angle that's directed toward the bottom of the pool. One way to remember it: Point the jets at 4 o'clock or 7 o'clock and ensure that the jets are not pushing water toward the skimmers.Why does my Salt Cell say no flow?
The “No Flow” light indicates that the flow switch is not detecting sufficient water passing through. Check the following: cleaning the cell or the filter (see how to backwash a DE Filter or Clean a Cartridge Filter). Replace the flow sensor.Why is my salt chlorinator not working?
The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.What should pressure be on Intex sand filter?
If anything could be considered “normal”, it would be about 10 psi. Most filter systems are designed to operate in the 5-15 or 10-20 psi range. The way to find out your particular correct pool filter pressure is to clean or backwash the filter thoroughly and empty the pump and skimmer baskets.What kind of salt do you use for Intex saltwater system?
Connect the water return (to the pool) hose to the adaptor A (05CG-11) on the saltwater pool system with a hose clamp (5F21). Use only sodium chloride (NaCl) salt that is at least 99.8% pure.Is it OK to run pool pump 24 hours a day?
The size of your pool, the efficiency of your pump and filter, and how dirty your pool is are just some of the factors you need to consider. Nevertheless, most pool cleaning professionals would advise against running a pool pump for more than 8 hours a day.Do you run pool pump while swimming?
Chemicals that you add to your pool while the water is circulating don't need to be recirculated; they will stay mixed even if you don't pump the water continually. Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time.Is it better to run a pool pump at night or day?
It may be cheaper to run the pump at night, but honestly you should run it 1 hour a day per 10 degrees of temperature at least, and it should be during the day. Running the pump at night should only be when you are doing a major chemical treatment such as algae clean-up.Why are my pool jets weak?
The most common reason for weak jets is an air leak. An air leak would come from the suction side of the system. This would be the area between the skimmer and the pump. One way to determine if you have an air leak is by looking for air bubbles coming out of the return jets.Why are my pool jets bubbling?
Air bubbles in your pool mean that air is being sucked into the line on the suction side of the pump. It's likely happening because of one of these issues: The pool water level is too low. The strainer pot lid isn't on tight or its O-ring is loose/absent/compromised.How deep should pool returns be?
Though returns have traditionally been placed 12 to 18 inches below the water's surface, more professionals are recommending that they be installed closer to the floor. The idea started in the 1980s when rebel inventor Mark Urban created a floor jet specifically for the purpose of introducing heated water.How do I know if my pool has a pressure side leak?
You can do the “bucket test” on your pool to measure evaporation. Place a bucket of water beside the pool and mark both the water in the bucket and the pool water level. Wait 24 hours then check the loss of both. If the pool loses more water than the bucket, then you have a leak.Why does my pool vacuum not have suction?
Rule out the obvious causes of poor vacuum first. Make sure the water level in the pool is sufficient and air is not being sucked in through skimmer inlets. Add water to the pool to submerge the skimmers if necessary. Verify that the pump strainer basket and the skimmers are free of debris that may obstruct water flow.Why is my vacuum not picking anything up?
The most common cause of loss of suction is that the filters have become blocked. They may require cleaning or replacing. Another cause could be that the vacuum cleaner hose is blocked. First unplug the vacuum cleaner.Why does my Intex saltwater system keep saying low salt?
The pool pump filter is so small, that if you don't keep it cleaned out several times a day, it clogs and seriously decreases the water flow, causing a low salt reading and low chlorine output, due to the fact that the water is not moving quickly and strong enough through the SWS.What happens if you put too much salt in a saltwater pool?
An overly salted pool will generally not be a major problem (aside from salty-tasting water), but at levels over 6000 ppm there may be corrosion damage to some of the metallic equipment.How do I make my saltwater pool crystal clear?
To get rid of cloudiness, you will have to do a liquid chlorine shock to raise the level of free chlorine (since the chlorine produced by the generator is not enough; a chlorine generator just assists you in maintaining the level of free chlorine).Should you shock a saltwater pool?
So, not only is shocking a saltwater pool okay, but it's actually important to your pool's health. Shocking is the process in which you overload your pool with chlorine (3-5 times the normal amount) to improve your pool's cleanliness and kill off organic matter.Can you add baking soda to a salt water pool?
A rule of thumb is 1.5 lbs. of baking soda per 10,000 gallons of water will raise alkalinity by about 10 ppm. If your pool's pH tested below 7.2, add 3-4 pounds of baking soda. If you're new to adding pool chemicals, start by adding only one-half or three-fourths of the recommended amount.How much salt do I add to my saltwater pool?
For complete disinfection, salt should be added to water to achieve a salinity rate of 0.4%. To obtain the ideal salt level for the pool, if the pool is devoid of salt, 16 kg (approx. 35 lbs) of salt should be applied for every 4000 liters (approx. 1000 gallons).How do I add salt to my pool for the first time?
To add salt, turn on your filter pump and add the salt directly to your pool water. Use a brush to help the salt dissolve and to prevent the salt from piling up on the bottom of your pool. Run your pump for 24 hours to help distribute the salt evenly throughout your pool.Do you put chlorine tablets in a saltwater pool?
A saltwater pool is an alternative to a traditional chlorine pool. Although you don't add chlorine tablets to a saltwater pool, it does still contain chlorine. It just has a smaller amount that's generated through the filter system. A saltwater pool contains 10 times less salt than the ocean.How much salt do I put in my saltwater Intex?
The ideal salt level in the pool water is between 2500-3500 ppm (parts per million) with 3000 ppm being optimal. A too low salt level will reduce the efficiency of the Saltwater System and result in low chlorine production.How do I add salt to my Intex above-ground pool?
Add one 25-pound bag of salt for every 1,000 gallons of water. Do not use yellow or iodine salt. Go to a pool supply company, and get salt for the pool. If you're converting your pool from a chlorine-treated pool to a salt water pool, wait two days, so the chlorine dissipates.Can an Intex pool be saltwater?
But what you might not know is that they can be easily converted to become a saltwater Intex pool. Switching from chlorine to saltwater can be a great choice for pool owners who have sensitivities or children with allergies and for those who don't want to be caught up on the incoming chlorine shortage.Can I add a second return to my above ground pool?
It's nice to add a new return line far away from the existing one, but you will have to do some extra plumbing. When the returns are close, they can be attached or plumbed together above the ground.Which way should your pool circulate?
It's good practice to point your return jets in a direction that will circulate the water in your pool. If your pool only has one jet, point the jet toward the skimmer and downward. This will circulate the water, and push the water at the bottom of the pool to the surface.Should pool pump be full of water?
It is designed to be filled with water at all times. If the pump is operated dry, it will burn out the motor and cause you to have to replace an expensive piece of pool equipment. If a pump is allowed to operate dry, it will build up heat that will melt the pump and possibly surrounding plumbing fixtures.Is it safe to swim in foamy pool water?
Swimming pool foam can be a huge distraction in and outside of your pool. Foam, or bubbles, make the water feel sticky and can make swimming uncomfortable for some. Good news for the kids, though, a foamy pool is safe to swim in. Still, we always recommend getting rid of the foam as soon as possible.Should I turn off pool pump when raining?
To prevent potentially dangerous electrical issues, it's imperative that you turn off the power to your pool equipment — such as pumps, motors, filters, heaters, chlorinators, and lighting fixtures. Even if you turn off the power to your pool equipment, it can still be damaged by wind, rain, and debris.Is it better to run a pool pump at night or day?
It may be cheaper to run the pump at night, but honestly you should run it 1 hour a day per 10 degrees of temperature at least, and it should be during the day. Running the pump at night should only be when you are doing a major chemical treatment such as algae clean-up.Do pool pumps use a lot of electricity?
One of the most significant consumers of energy in homes with swimming pools are pool pumps, which keep pools clean by circulating water through filters. Pool pumps can consume 3,000 to over 5,000 kWh per year.How often should I run my saltwater chlorinator?
On average, most pools will need the saltwater generator to be on 8-12 hours per day. This will produce adequate levels of chlorine to properly sanitize the pool's water.How long should I run my Intex salt chlorinator?
First make sure you run just the filter pump for at least six hours to ensure the salt you've added has dissolved properly. Then you can run the salt water system fir the time recommended in the manual. If it's very hot and sunny you should run it for four hours for the 16'x48" pool.Why is my Intex salt water pool green?
While green algae are endemic in salt water pools, they are the easiest to kill. Green algae tend to grow during summers when the temperatures can get high. They float freely in the pool, making the water green. You might even see them growing on the bottom of the pool, on the walls, or in the crevices.What kind of sand do I use for Intex sand filter?
The recommended type is No. 20 grade silica sand, with specification of 0.45 to 0.85mm (0.018 to 0.033 inches) with a Uniformity Coefficient less than 1.75. Too fine of a grade of sand will clog too quickly, and too soft of a sand will break up and also cause clogging.How do you know if your sand filter is working properly?
Add diatomaceous earth (DE) to your pool skimmer, stick to around a scoop or two – no more than the size of a 1lb coffee cup. The moment you do this, go to the pool jets to see if it is returning DE into the pool, or if the water suddenly looks cloudy. If it is, you likely have an issue with your filter.Why does my Intex saltwater system keep saying low salt?
The pool pump filter is so small, that if you don't keep it cleaned out several times a day, it clogs and seriously decreases the water flow, causing a low salt reading and low chlorine output, due to the fact that the water is not moving quickly and strong enough through the SWS.How do you know if salt chlorinator is not working?
Test the water that water has just left the chlorinator - it should have a very high chlorine reading. (Remember that if it is extremely high it may bleach the test tablet so you may have to dilute the water you are testing). If there is no chlorine reading, the chlorinator will not be working.Why does my salt water pool look cloudy?
Just like a chlorine-based pool, saltwater pools turn cloudy when chemicals are not balanced. You need to ensure that all chemicals are balanced all the time to avoid cloudy water and growth of algae. The major causes of cloudiness are chlorine, pH, Salinity, total alkalinity, cyanuric acid, and calcium hardness.Is 3800 ppm salt too high?
Generally it's better to have the level on the high side than low, so 3800 should be fine.Can I use vinegar to clean my salt cell?
As a thumb rule, go for a mild solution with a perfect blend of water and vinegar. Soak the saltwater cell or hot tubs (as the case may be) in a container with vinegar solution for a night. The solution can remove all sorts of remaining debris within a fortnight.How long should a pool salt cell last?
This is all possible thanks to your pool's salt chlorine generator cell. With proper care, a cell will last about five years. Eventually, though, it will need to be replaced.Why does my salt generator say low salt?
A low salt warning tells you that the salt level in the pool is too low for the chlorinator to generate chlorine. Usually, the low light warning comes on when the salt level is below 2000 ppm and 3500 ppm.